Ballpark Lab

Siding Cost Calculator / North Carolina

North Carolina siding estimate

Siding Cost in North Carolina (2026)

Re-siding a house in North Carolina runs roughly 7% below the national average on installed labor, which we apply to the per-square-foot rate for every material. Last updated July 6, 2026.

A typical two-story vinyl re-side in North Carolina

45 × 30 ft footprint (150 ft perimeter), 19 ft walls, gable roof, 12 windows, 2 doors, 1 garage door, no tear-off — a clean baseline before you customize.

$10k – $39k
Confidencehigh

Material takeoff

Siding to order
32 squares
Starter strip
150 lf
Housewrap
3,075 sq ft
Outside corner posts
76 lf
Vinyl boxes (2 squares/box)
17 boxes

Cost breakdown

vinyl siding (installed)
$10k – $39k
Permit allowance
$100 – $400
Total
$10k – $39k
Most likely
$22,939
  • Wall area = footprint perimeter × 19 ft grade-to-eave height; a 1.5:1 rectangle is assumed when only the perimeter is known.
  • 2 gable triangles estimated at a 6/12 pitch for the "gable" roof style.
  • Openings reduced at 75% of their area (trim and cuts eat part of the saving); waste factor 13%.
  • Coastal counties enforce wind fastening schedules; inland permits vary.

Where these numbers come from: installed-price surveys + regional references, updated July 6, 2026 — see our methodology.

What drives siding cost in North Carolina

North Carolina splits at the coast: hurricane-exposed counties enforce wind fastening schedules and favor rated vinyl or fiber cement with corrosion-resistant fasteners, while inland the market looks like the broader South — fiber cement rising, vinyl on volume, wood fading because of humidity and rot. Coastal salt air punishes bargain fasteners and trim. The mild 12-inch frost line means no special cold-weather detailing. Labor sits just below the national average, highest in Charlotte and the Triangle.

Estimate your siding in North Carolina

House details

This estimates wall area from your footprint — we adjust for stories, gables, windows and doors.

The long side of the house, in feet.

The short side, in feet.

Footprint perimeter: 150 ft (2 × (length + width))

Grade to eave, in feet — pre-filled from the story count.

Gable ends add sided triangles; hip and flat roofs don't.

Openings to subtract
Windows
12
Doors
2
Garage doors
1

Trim and cuts eat part of the saving — most estimators don't subtract 100%.

Estimated total
$9,845–$39,382
Vinyl · 32.3 squares
Low $10kMost likely ~$22,939High $39k

$10k – $39k · $7 per square foot (/sq ft) · 32.3 siding squares (1 square = 100 sq ft)

Confidencehigh

Material takeoff

Siding to order
32 squares
Starter strip
150 lf
Housewrap
3,075 sq ft
Outside corner posts
76 lf
Vinyl boxes (2 squares/box)
17 boxes

Cost breakdown

vinyl siding (installed)
$10k – $39k
Permit allowance
$100 – $400
Total
$10k – $39k
Most likely
$22,939
  • Wall area = footprint perimeter × 19 ft grade-to-eave height; a 1.5:1 rectangle is assumed when only the perimeter is known.
  • 2 gable triangles estimated at a 6/12 pitch for the "gable" roof style.
  • Openings reduced at 75% of their area (trim and cuts eat part of the saving); waste factor 13%.
  • Coastal counties enforce wind fastening schedules; inland permits vary.

Compare materials

VinylSelected
$10k – $39k
Fiber cement
$16k – $46k
Engineered wood
$20k – $49k
Wood
$23k – $56k

The same house in each material — same size, openings, site, and state.

iBallpark estimate for planning, not a bid. Wall area is estimated from your footprint — a contractor will measure each wall. Excludes hidden rot, sheathing replacement, and structural repairs found at tear-off. Get 3 local quotes before signing.

Data: U.S. EIA · OpenEI URDB · Google Solar · NREL PVWatts · DSIRE · IRS · ENERGY STAR · industry surveys — see all sources

Frequently asked questions

How much does siding cost in North Carolina?
Re-siding a typical two-story house (45 × 30 ft footprint, about 32.3 squares) in North Carolina runs about $10k – $39k in vinyl, with labor roughly 7% below the national average.
Is fiber cement worth it over vinyl in North Carolina?
The same house in fiber cement runs about $16k – $46k versus $10k – $39k in vinyl. Fiber cement costs more up front but resists impact, fire, and fading better — often the better long-term buy in harsh climates.
Do I need a permit to re-side a house in North Carolina?
Coastal counties enforce wind fastening schedules; inland permits vary.

Siding costs in other states